Read Chapter wise CCNA 3 Exam Answers (v5.1 + v6.0) 1. In which scenario will the use of EIGRP automatic summarization cause inconsistent routing in a network?
2. What is the purpose of a Null0 route in the routing table?
3. Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency. What action should be taken to solve this problem?
4. Fill in the blank. Do not use abbreviations. Correct Answer: passive-interface* 5. Refer to the exhibit. After the configuration shown is applied on router R1, the exhibited status message is displayed. Router R1 is unable to form a neighbor relationship with R2 on the serial 0/1/0 interface. What is the most likely cause of this problem?
6. By default, how many equal-cost routes to the same destination network will EIGRP install in the routing table? 7. Open the PT Activity. Perform the tasks in the activity instructions and then answer the question. R1 and R2 could not establish an EIGRP adjacency. What is the problem?
8. Refer to the exhibit. All networks are active in the same EIGRP routing domain. When the auto-summary command is issued on R3, which two summary networks will be calculated on R3? (Choose two.)
9. Which three statements are advantages of using automatic summarization? (Choose three.)
10. Refer to the exhibit. Which two conclusions can be drawn from the exhibited configuration? (Choose two.)
11. What is the administrative distance of externally learned EIGRP routes? 12. Which routing protocol supports unequal-cost load balancing on Cisco routers? 13. Refer to the exhibit. Which two routes will be advertised to the router ISP if autosummarization is disabled? (Choose two.)
14. Which two steps must be taken in order to send a default route to other EIGRP routers? (Choose two.)
15. Refer to the exhibit. Remote users are experiencing connectivity problems when attempting to reach hosts in the 172.21.100.0 /24 network. Using the output in the exhibit, what is the most likely cause of the connectivity problem?
16. Refer to the exhibit. An administrator wants EIGRP on Router1 to load balance traffic to network 2001:db8:11:10::/64 across two interfaces. Currently traffic is using only interface GigabitEthernet0/1. A second route, not in the routing table, is available with a metric of 264000. What value is needed in the variance command to make EIGRP put the second route into the routing table? 17. Refer to the exhibit. Considering that R2, R3, and R4 are correctly configured, why did R1 not establish an adjacency with R2, R3, and R4?
18. When a Cisco router is configured with fast-switching, how are packets distributed over equal-cost paths?
19. What is the default maximum amount of bandwidth that can be used for exchanging EIGRP messages on an EIGRP-configured interface? 20. Fill in the blank. Do not use abbreviations. The command to propagate the default route from the router Border to the rest of the EIGRP domain is Border(config-router)# _________ Correct Answer: redistribute static* 21. Refer to the exhibit. Which statement is supported by the output?
22. Which command can be issued on a router to verify that automatic summarization is enabled?
23. Assuming that EIGRP is enabled on both routers and automatic summarization is enabled, what must be configured to ensure that R1 will be able to reach the 2.2.2.0/24 network?
24. Two routers, R1 and R2, share a 64 kb/s link. An administrator wants to limit the bandwidth used by EIGRP between these two routers to 48 kb/s. Which command is used on both routers to configure the new bandwidth setting?
25. Refer to the exhibit. Router R3 is receiving multiple routes through the EIGRP routing protocol. Which statement is true about the implementation of summarization in this network?
26.Which protocol is used by EIGRP to send hello packets? 27. When an EIGRP-enabled router uses a password to accept routes from other EIGRP-enabled routers, which mechanism is used?
28. What is the purpose of using protocol-dependent modules in EIGRP?
29. If all router Ethernet interfaces in an EIGRP network are configured with the default EIGRP timers, how long will a router wait by default to receive an EIGRP packet from its neighbor before declaring the neighbor unreachable?
30. Which statement describes a characteristic of the delivery of EIGRP update packets?
31. Which destination MAC address is used when a multicast EIGRP packet is encapsulated into an Ethernet frame?
32. Why would a network administrator use a wildcard mask in the network command when configuring a router to use EIGRP?
33. Refer to the exhibit. Which command should be used to configure EIGRP to only advertise the network that is attached to the gigabit Ethernet 0/1 interface?network 172.16.23.64 0.0.0.63*
34. Which EIGRP route would have the preferred administrative distance?
35. Where are EIGRP successor routes stored?
36. Which table is used by EIGRP to store all routes that are learned from EIGRP neighbors?
37. How do EIGRP routers establish and maintain neighbor relationships?
38. Which command or commands must be entered on a serial interface of a Cisco router to restore the bandwidth to the default value of that specific router interface?
39. Which command is used to display the bandwidth of an interface on an EIGRP-enabled router?
40. A new network administrator has been asked to verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP metrics are measured by using static values on a Cisco device? (Choose two.)
41. Which three metric weights are set to zero by default when costs in EIGRP are being calculated? (Choose three.) 42. Refer to the exhibit. R2 has two possible paths to the 192.168.10.4 network. What would make the alternate route meet the feasibility condition?a reported distance less than 3523840*
43. What is indicated when an EIGRP route is in the passive state?
44. Refer to the exhibit. Which two networks contain feasible successors? (Choose two.)192.168.71.0*
45. Fill in the blank. 46. Which two EIGRP packet types are sent with unreliable delivery? (Choose two.)
47. What is identified within the opcode of an EIGRP packet header?
48. An administrator issues the router eigrp 100 command on a router. What is the number 100 used for?
49. What information does EIGRP maintain within the routing table?
50. Refer to the exhibit. R3 has two possible paths to the 172.16.99.0 network. What is the reported distance of the feasible successor route?
51. What is the multicast address used by an EIGRP-enabled router operating with IPv6?
52. Which configuration is necessary to ensure successful operation of EIGRP for IPv6?
53. Fill in the Blank. Use the abbreviation. 54. Order the precedence in which an EIGRP router would choose the router ID. (Not all options are used.) Place the options in the following order: 55. 30. Match the correct version of EIGRP with the EIGRP features. (Not all options are used.) Place the options in the following order: 56.Launch PT – Hide and Save PT Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
57. Refer to the exhibit. R3 has two possible paths to the 172.16.99.0 network. What is the reported distance of the feasible successor route?
58. Which two EIGRP packet types are sent with reliable delivery? (Choose two.)
More Resources |